e26f1d14

4.4.2. Removal and installation of the engine

Removal

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. At the corresponding complete set remove protection of a case of engine/transmission.
  3. Empty the cooling system (see the Head the Current leaving and service).
  4. Merge motive oil (see the Head the Current leaving and service).
  5. Remove an air inlet and an air sleeve (see Power supply systems, managements of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases).
  6. Remove components of the drive of a butterfly valve (see Power supply systems, managements of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases).
  7. Remove the top and lower hoses of a radiator of the cooling system (see the Head of the Cooling system, heating, ventilation and air conditioning).
  8. Disconnect a reception pipe of system of production of the fulfilled gases (see Power supply systems, managements of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases).
  9. Disunite all electric sockets located in a motive compartment: a starter, the generator, ignition coils, the coupling of the K/V compressor, fuel injectors, a lambda probe(s) (depending on a complete set), the sensor of provision of a bent shaft (models with AT, - on models with RKPP the electrical wiring is disconnected from the CKP sensor from under the car), the sensor of measurement of mass of air (MAF), the generator, the sensor of provision of a butterfly valve (TPS), the valve of a purge of a coal adsorber, the valve regulator of turns of idling (IAC), and so forth.
  10. Disconnect from the engine all vacuum hoses, including lines of strengthening of brakes and the drive of switching of stupichny couplings of forward wheels (at the corresponding complete set), and also hoses of cooling and fuel paths (do not forget about a hose of withdrawal of fuel evaporations on assembly of a coal adsorber).

Before a detachment of fuel hoses do not forget to dump pressure in a path of system of injection of fuel (see the Head of the Power supply system, management of engine/decrease in toxicity of the fulfilled gases and production of the fulfilled gases)!

  1. Remove a forward lattice (see the Head Kuzov).
  2. On models of the corresponding complete set remove the fan of the K/V condenser, then actually the K/V condenser (see the Head of the Cooling system, heating, ventilation and air conditioning).
  3. Remove a cooling system radiator (see the Head of the Cooling system, heating, ventilation and air conditioning).
  1. On models of the corresponding complete set pick up the К/В compressor phone.
  1. Take off belts of the drive of auxiliary units (see the Section Belts of the drive of auxiliary units).
  2. From under the car disconnect an electrical wiring of sensors of speed of the movement (VSS) and CKP (model with RKPP), and also sensors switches of fires of a backing and the alarm indicator of activation of the all-wheel drive mode.
Location of sockets of an electrical wiring of VSS sensors (C), CKP (D) and sensors switches of fires of a backing (A) and the alarm indicator of activation of the all-wheel drive mode (V) - model with RKPP.
Location of the socket of an electrical wiring of the VSS sensor - model with AT.
Location of sockets of an electrical wiring of sensors switches of fires of a backing (1) and the alarm indicator of activation of the all-wheel drive mode (2) - model with AT.
  1. Remove the sensor switch of the alarm indicator of the four-wheel drive.
  1. Remove a starter (see the Head Sistemy of electric equipment of the engine).
  1. Prop up a basic beam of transmission / the transfer case a suitable jack, then turn out bolts of fastening of RKPP/AT to the engine (see the Head the Five-step manual box of gear shifting or Automatic transmission).
  1. Turn out bolts of fastening of a beam and lower transmission on a jack.
  2. Fix lifting slings in lifting eyes of the engine and hang out the last so that support of its suspension bracket were completely unloaded.
  3. Turn out bolts of fastening of support and at the top carefully take the engine from a motor compartment of the car.

Installation

 PERFORMANCE ORDER

  1. Installation is made as it should be, the return to an order of dismantle of components. Track correctness of restoration of initial all lines of communication of connection. Remember that all carving fixture has to drag on with the required effort.