14:13. Replacement of lamps and check of serviceability of functioning of external lighting fixtures
Headlights
Replacement of lamps
|
|
Halogen lamps are filled with the gas which is under pressure and at damage can "blow up"! Try not to touch a lamp flask barehanded, - the fatty spots left on glass can be the reason of an exit of a lamp out of operation as a result of a local overheat. For additional safety at service of halogen lamps it is necessary to put on goggles! |
|
|
- Open a cowl.
|
|
- Disconnect the electrical wiring brought to the back party of a block headlight.
|
|
|
- Release a wire spring clamp.
|
- Release a lamp from three grooves in assembly of a block headlight and establish instead of it replaceable.
- Assembly is made as it should be, the return to an order of dismantle of components, - track reliability of fixing of components.
|
|
Check of serviceability of functioning of the switch of the choice of the mode of functioning of headlights
|
|
- By means of an ohmmeter check correctness of distribution of conductivity between plugs of the contact socket of an electrical wiring of a block headlight from a plait in various provisions of the lever of the left understeering switch (see the table). In case of need make the corresponding corrections / replace assembly of understeering switches.
Check of serviceability of functioning of the switch of the choice of the mode of functioning of headlights
|
|
The forward combined lamps
Replacement of lamps
|
|
- The forward combined lamps are located from outer sides of block headlights and carry out a role of indexes of turns and parking/marker lights.
|
|
- Open a cowl and find a white plastic ring in the corresponding corner of a motive compartment.
|
- Having pulled for a ring, release a spring clamp from a wing mudguard.
- Accurately remove assembly of the forward combined lamp.
|
|
- Having turned counterclockwise before combination of lock uvulas with reciprocal grooves, take from lantern assembly a cartridge with the lamp put in it.
|
- Having pressed and having turned the lamp equipped with a bayonetny socle, take it from the boss.
- Put a replaceable lamp in a cartridge and make assembly of a lamp, - act as it should be, the return to an order of dismantle of components.
|
|
For a zashchelkivaniye of a spring clamp of assembly pull for a plastic ring again. |
|
|
Check of serviceability of functioning of switches of indexes of turns / marker lights
|
|
- By means of an ohmmeter check correctness of distribution of conductivity between plugs of the contact socket of an electrical wiring of the forward combined lamp from a plait in various provisions of the lever of the left understeering switch (see the table). In case of need make the corresponding corrections / replace assembly of understeering switches.
Check of serviceability of functioning of switches of forward indexes of turn / marker lights
|
|
Stoplight of the top level
Replacement of a lamp
5-door models
|
|
|
|
- By means of the small screw-driver carefully drown the central pins of fixing clamps of a back cover of a stoplight of the top level.
|
- Take clamps and uncover, - try not to lose components of clamps.
|
|
- Having turned on 1/4 turns counterclockwise, release a cartridge with the lamp established in it from a reflector of lantern assembly.
|
- Having pulled, take a paw from the boss and establish replaceable on its place.
- Assembly is made as it should be, the return to an order of dismantle of components.
|
|
Cabriolet models
|
|
|
|
- Turn out fixing screws and remove a lens of lantern assembly.
|
|
|
- Accurately take a lamp from a casing and, having turned a cartridge on 1/4 turns counterclockwise, release it from a reflector.
|
- Having pressed and having turned, take the lamp equipped with a socle of bayonetny type from the boss and establish replaceable on its place.
- Assembly is made as it should be, the return to an order of dismantle of components.
|
|
The back combined lamps
Replacement of lamps
5-door models
|
|
|
|
- Having pulled on itself for the provided dredging, accurately uncover access to a back loudspeaker.
|
- Having wrung out a lock uvula, disunite the contact socket of an electrical wiring.
|
|
- Give four nuts of fastening of lantern assembly.
|
|
|
- Remove a lamp from the body panel of the car.
|
|
|
- Having combined lock uvulas with reciprocal grooves, take the failed lamp and establish replaceable on its place.
|
- Assembly is made as it should be, the return to an order of dismantle of components.
|
|
Cabriolet models
|
|
|
|
- Uncover access to the back combined lamp.
|
|
|
- Having wrung out a lock uvula, disunite the contact socket of an electrical wiring, then release four fixing nuts and remove lantern assembly.
|
|
|
- Having combined lock uvulas with reciprocal grooves, take the failed lamp and establish replaceable on its place.
|
- Assembly is made as it should be, the return to an order of dismantle of components.
|
|
Check
All models
|
|
- By means of an ohmmeter check correctness of distribution of conductivity between plugs of the contact socket of an electrical wiring of the back combined lamp from a plait in various provisions of the corresponding switches / датчиков-выключателей (see the table). In case of need make the corresponding corrections / replace the failed elements.
Check of serviceability of functioning of switches / датчиков-выключателей activation of lamps of the back combined lamps
|
|
Lamps of illumination of registration plate
Design and details of installation of lamps of illumination of registration plate
Replacement of lamps
|
|
- Turn out two fixing screws and remove a lens of a faulty lamp of illumination of registration plate.
|
|
- Having pulled down, release a lamp holder from lantern assembly, then take (also just pull a lamp down) from it the fused lamp and establish replaceable on its place.
|
- Establish into place a lamp holder and a lens, screw fixing screws.
|
|
