e26f1d14

13.2.9. Dismantling, removal, installation and adjustment of doors

The design of drives of door locks and window regulators is in detail considered in the Sections Design of the Drive of Door Window Regulators and Design of the Drive of Door Locks.

Forward doors

Design of assembly of a forward door

1 — the Internal handle
2 — the Panel of an internal upholstery
3 — the Insulating screen
4 — the lock Drummer
5 — the Activator of the door lock
6 — the Armrest
7 — the Directing trench of a window opening
8 — Glass
9 — Assembly of the regulator of a window regulator
10 — the Guide flew down
11 — Assembly of the door lock
12 — a door Frame

13 — the External handle
14 — the Sealant
15 — the door course Limiter
16 — a limiter Finger
17 — Loopy assembly
18 — the Molding
19 — the Overlay of a loudspeaker
20, 21 — Uplotniteli lower
22 — the Boot
23 — the Pocket in an armrest / поручневая the handle
24 — the Arm of the poruchnevy handle
25 — the Cylinder of the door lock

Dismantling, removal and installation

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Remove the panel of an internal upholstery of a door.
  1. Turn out two fixing screws and remove an arm of the poruchnevy handle.
  1. Turn out four fixing bolts, release from clamps on a doorframe a plait of an electrical wiring and the loudspeaker of a loudspeaker. Disunite the contact socket and remove the loudspeaker.
  1. Separate the film insulating screen from a door.
  2. Connect the battery and, - if disconnected, - a window regulator drive switch electrical wiring. Include ignition and half lower door glass. Switch off ignition and disconnect a negative wire from the battery.
  3. Through an aperture in a doorframe turn out two bolts of fastening of glass to the window regulator regulator.
  1. Having inclined forward, accurately extract glass from a window opening of a door.
  1. Disconnect an electrical wiring from a window regulator regulator drive electric motor, give six nuts and through a service opening take assembly of the regulator from a doorframe.
  1. Remove the directing trench (1) of a window opening.
  1. Turn out one fixing bolt and through a service opening take a glass guide from a doorframe.
  1. Rotating counterclockwise, remove the door lock otpuskaniye button.
  1. Disconnect two driving rods from the external handle of a door.
  1. Turn out three fixing bolts and through a service opening take castle assembly from a doorframe.
  1. On the right door give two fixing nuts and remove the lock activator.
  2. Give two fixing nuts and remove the external handle of a door.
  3. Remove a door rear-view mirror (see the Section Removal and installation of door rear-view mirrors).
  4. Disunite five contact sockets of the electrical wiring laid in a doorframe.
  5. Through a service opening take an electrical wiring from a frame.
  1. Accurately beat out the hammer a door course limiter finger, - try not to damage a paint and varnish covering.
  1. Give two fixing nuts and remove the limiter.
  2. Remove a boot of a door threshold.
  1. Turn out four loopy bolts and remove a door from the car, - use the help of the assistant.
  1. In case of need remove panels of finishing of a door threshold and the lower section of a rack In and remove a sealing strip from an adjusting flange of a doorway.
  1. Installation is made as it should be, the return to an order of dismantle of components, - track observance of requirements of Specifications of the Head Kuzov to efforts of tightening of carving fixture.
  2. Check correctness of landing of a door in a body aperture, in case of need make the corresponding adjustment.

Adjustment

 PERFORMANCE ORDER

  1. Release loopy bolts and level a door in an aperture of rather surrounding body panels. Having finished adjustment, do not forget to tighten bolts with the required effort.
  2. Check correctness of a zashchelkivaniye of the door lock. In case of need release fixing bolts and correct position of the drummer.

By removal of the drummer in the horizontal direction the provision of the rear edge of the closed door concerning a rack surface can be leveled.

Back doors

The order of performing procedures is similar described above for forward doors adjusted for differences in a design of assemblies.

Design of assembly of a back door

1 — the Internal handle
2 — the Armrest
3 — the Panel of an internal upholstery
4 — the Button of switching off of the lock
5 — the Insulating screen
6 — the Central directing trench
7 — the Directing trench of a window opening
8 — the lock Drummer
9 — the window regulator drive Handle
10 — Glass (the mobile and fixed sections)
11 — Assembly of the regulator of a window regulator
12 — Assembly of the door lock

13 — a door Frame
14 — the Activator of the door lock
15 — the External handle
16 — the Sealant
17 — the door course Limiter
18 — a limiter Finger
19 — the Central trench
20 — Loopy assembly
21, 24, 25 — Uplotniteli
22 — the Molding
23 — Poruchnevaya the handle

Back door

Design of assembly of a door of a back

1 — Back glass
2 — the Molding
3 — a door Frame
4 — the Sealant

5 — the lock Drummer
6 — the Panel of an internal upholstery
7 — Э / the screen wiper drive motor
8 — the Screen wiper
9 — the Gas-filled telescopic emphasis

Dismantling, removal and installation

 PERFORMANCE ORDER

  1. Disconnect a negative wire from the battery.
  2. Open a back door.
  3. Turn out two fixing screws and uncover a door stoplight of the top level.
  4. Disconnect an electrical wiring, turn out two fixing screws and remove a stoplight lamp.
  5. Having disunited two contact sockets (on one from each party of door assembly) disconnect an electrical wiring of a heater of back glass.
  6. Remove the grounding uvula of fixing of the right socket of an electrical wiring of a heater.
  7. Release 12 clamps and remove the lower panel of an internal upholstery of a door.
  8. Remove a plastic cover to the left of the central aperture in a doorframe and through a service opening disunite three contact sockets of an internal electrical wiring of a door.
  9. Disunite three one-contact sockets located in the left top angle of door assembly.
  10. Take from a landing opening in the left top corner of a door the rubber plug through passage and release an electrical wiring plait from a doorframe.
  11. Take pins from the socket of a stoplight and one pin from the left socket of a heater of glass.
  12. Accurately release electrical wiring plaits from cable channel in a doorframe, and also from the protection cover and the rubber plug through passage.
  13. Fix cases of sockets the pins.
  14. Release the right plug through passage from a doorframe, having provided thereby access to a tube of supply of liquid to a nozzle of washing of back glass.
  15. Remove a nozzle and disconnect from it the giving tube.
  1. Having secured with support of the assistant, reliably record a back door in open situation and disconnect spherical support of a telescopic emphasis from a door.
  1. For the purpose of simplification of the procedure of installation squeeze a protective cover and fix the socket of the giving hose from its outer side.
  2. Disconnect the giving hose from the socket and remove it from the car.
  1. Turn out on one loopy bolt.
  1. Having made sure of reliability of fixing of a door, turn out the remained two bolts and remove door assembly from the car.
  2. Installation is made as it should be, the return to an order of dismantle of components, - track observance of requirements of Specifications of the Head Kuzov to efforts of tightening of carving fixture.
  3. Check correctness of landing of a door in a body aperture, in case of need make the corresponding adjustment.

Adjustment

 PERFORMANCE ORDER

  1. Make control measurements And, B and D and make sure that results of measurement do not exceed the limit of admissible ranges, in case of need release loopy bolts and spherical support of a telescopic emphasis and correct the provision of a door in a body aperture. Having finished adjustment, tighten bolts and support with the required effort.
  1. Make control measurement With, - the provision of the wedges established on side stacks of a body aperture defines the angle of closing of a door on a view of the Village. If the result of measurement exceeds admissible value, shift wedges outside, - for increase in the size it is necessary to shift, on the contrary, wedges towards an aperture.