e26f1d14

13.3.3. Seats - the general information, check of a state, removal and installation of components

The design and details of installation of components of seat belts are shown in the Section Design and a detail of installation of components of seat belts, removal of the worked emergency natyazhitel.

General information

Design and details of installation of seats

1 — the Side cover of the basis
2 — the Lever of adjustment of an inclination of a back
3 — the Lever of adjustment of a configuration of a lumbar emphasis of a back
4 — the Lever of an otpuskaniye of the mechanism of fixing of a sled

5 — Head restraints
6, 10 — Backs
7, 11 — Pillows
8 — Loopy assemblies
9 — the Clamp

Front seats

Front seats are installed separately and are regulated in an individual order. A sled of each seat fastens to guides of the frames attached to a car floor by means of three bolts and one nut everyone. Levers of the drive of an otpuskaniye of mechanisms of fixing of a sled are removed under forward edges of pillows and allow to carry out adjustment of provision of seats in the longitudinal direction. On one adjusting lever it is brought to the outer edges of assemblies of seats, - procrastination of the handle of the lever leads to an otpuskaniye of a clamp of a back up and allows to regulate an inclination of the last by its compulsory push-up down (at a back otpuskaniye it is automatically transferred to extreme forward situation under the influence of a special spring). On the right also the lever of adjustment of a configuration of a lumbar emphasis is located on a back of a driver's seat.

Back seat

The back seat with a continuous pillow can be equipped both with the integral, and divided into two individual sections back. Backs are equipped with the built-in head restraints. The pillow has loopy fastening to a floor that allows to throw back assembly of a seat with the translation it in vertical position forward, - the back (i) should be lowered previously forward. Fastening of assembly and to a floor is carried out by means of two bolts, two nuts and one back clamp. Fixing of a back(s) in vertical position is provided with two hooks which are built in in walls of the luggage compartment.

Check

 PERFORMANCE ORDER

  1. Check smoothness of the course of adjusting levers of front seats, estimate degree of wear of components of the fixing mechanisms. Replace defective parts.
  2. Make sure of reliability of tightening of all carving fixture, - in case of need bring up him with the required effort.
  3. Grease mobile components of a sled, driving levers and mechanisms of fixing.

Removal and installation of components

Backs of front seats

 PERFORMANCE ORDER

  1. Remove the handle of the lever of an otpuskaniye of the mechanism of fixing of a back.
  1. Dismantle decorative caps, turn out fixing bolts and remove a side cover of the basis of assembly of a seat.
  1. On a driver's seat turn out the fixing screw and remove the lever of adjustment of a configuration of a lumbar emphasis of a back.
  1. Remove ring clamps of fastening of an upholstery of a seatback.
  1. Turn out a loopy bolt of fastening of a back.
  1. For the purpose of ensuring access to fixture of a rotary fist of a back lift up an upholstery of the last up.
  1. Turn out fixing bolts, remove a rotary fist and separate a back from a pillow.
  1. Installation is made upside-down, - track observance of requirements of the Body Specifications to efforts of tightening of carving fixture.

Assembly of a back seat

 PERFORMANCE ORDER

  1. Having extended the push-button clamps located outside from head restraints, lower a back (and) seats forward.
  2. Turn out two fixing bolts and give two nuts of fastening of a pillow of a seat to a floor.
  3. Remove assembly of a back seat and take it from the car.
  4. In case of need turn out loopy bolts and separate a back (i) from a pillow.
  5. Installation is made upside-down, - track observance of requirements of the Body Specifications to efforts of tightening of carving fixture.